Ignition Systems - Spark Plug Wires

MSD Super Conductor 8.5 MM Big Block Chevy Wire Set

All Big Block Chevy marine engines with HEI male style distributorcaps.

Super Conductor 8.5 MM Spark Plug Wire has extremely low resistance and high RFI (radio frequency interference) suppression; a combination which would seem to defy the laws of physics. The low resistance is achieved through use of a helically wrapped, copper alloy conductor which is then wrapped around a ferro-magnetic impregnated center core.

MSD 8.5 MM Spark Plug Wire Set Big Block Chevy with Socket Distributor Cap

• Only 40-50 ohms resistance per foot of wire (lowest of any helically-wound wire)
• MSD Ignition Copper alloy conductors result in less spark energy loss so more reaches spark plugs
• Over 40 feet of conductor per foot of wire
• Conductors are wrapped around ferro-magnetic center cores, which effectively suppresses electro magnetic interference
• Outer sleeves consist of silicone and synthetic material for a strong resistance to heat, abrasion, and tearing
• Made in the USA
• 90 degree ends

"New" MSD Direct Fit Spark Plug wire set for Mercruiser 600/700 SCi Replaces Mercruiser #84-899330A09 and 84-899330A10

This MSD spark plug wire set has been custom built to replace the stock inferior OEM wire set found on Mercruiser's 600/700 SCi series of engines. Each spark plug wire is manufactured from MSD 8.5MM Helicore performance wire and provides 10X the spark energy of OEM wire sets. By delivering more spark to the spark plug efficiency and performance are achieved. 

Wire Lengths:

1. 33.5"
2. 36"
3. 34"
4. 33"
5. 25.5"
6. 32.5"
7. 22.5"
8. 25.25"

This MAX-VOLT spark plug wire set has been custom built to replace the stock inferior OEM wire set found on Mercruiser's 8.1L 496 series of engines. Each spark plug wire is manufactured from MAX-VOLT 8.8MM performance wire and provides 10X the spark energy of OEM wire sets. By delivering more spark to the spark plug efficiency and performance are achieved.  

Features

• Direct replacement for Mercruiser 496HO, 496MAG, and 8.1L
• 8.8MM BLACK SILICONE JACKETED & INSULATED
• MAG WIREWOUND CONDUCTOR
• 500-OHMS OF RESISTANCE PER FT
• A high strength synthetic mesh tape is used between the core material and jacket to strengthen the finished wire.
• Silicone jacketing provides high temperature and chemical resistance.
• Made in USA
• Wire diameters meet ISO 3806 Class E Type 4 standards
• 304 Stainless Steel 41-gauge (0.00275”) alloy with 57 turns per inch with a reactive latex coating.
• Class E Silicone / EPDM Wire Construction / SAE J2031 Rated Cable
  
• Operating Temperature Resistance Exceeds 450 Degrees Fahrenheit
  
• 500 ohm Kevlar Core, Ferrite Impregnated, Stainless Steel Wire “MAG” Wound
• Latex Silicone Layer Enhances Conductive Efficiency & Core Stability
• RFI and EMI Suppression
• EPDM Inner Insulation For Dielectric Strength
• Premium Core Provides Unmatched Strength and High Temperature Durability
• Braided Inner Tape to Provide Maximum Flexibility and Strength
• Tempered Silicone Outer Jacket
• OE Quality Terminals, Tips, Tubes
• Comes with Dielectric Grease and wire separators

"New" MSD Direct Fit Spark Plug wire set for Mercruiser 525 EFI Replaces Mercruiser #84-840955T01

This MSD spark plug wire set has been custom built to replace the stock inferior OEM wire set found on Mercruiser's 525 EFI series of engines. Each spark plug wire is manufactured from MSD 8.5MM Helicore performance wire and provides 10X the spark energy of OEM wire sets. By delivering more spark to the spark plug efficiency and performance are achieved.

These wires fit the serials numbers: OM900146 thru OM953619. Replaces Merc 84-840955T01

Wire Lengths:

1. 42"
2. 52.5"
3. 41"
4. 54.5"
5. 35.5"
6. 45"
7. 36.5"
8. 41"

"New" MSD Direct Fit Spark Plug wire set for Mercruiser 850SCi/1075SCi/120SCi

This MSD Performance spark plug wire set is designed as a upgrade to replace the stock factory OEM wire set found on Mercury Racing 850SCI, 1075SCI, and 1200SCI Supercharged engines. Each spark plug wire is custom tailored and manufactured from MSD 8.5MM Helicore performance wire and provides 10X the spark energy of OEM wire sets. By delivering more spark to the spark plug efficiency and performance are achieved. Replaces #84-842393A03 and #84-842393A04

MSD 8.5 MM 8.5 MM Super Conductor Spark Plug Wire Set, GM LS1, 1997-Present

Features:
• Made in the USA
• Custom fit for make and model listed.
• Wires are precut to exact specifications
• Bolt-on performance

Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference! In a single 8 inch length of Super Conductor Wire there is only 40 - 50 ohms of resistance! That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to it's great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective Electro Magnetic Interference (EMI) "choke". This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. The MSD's 8.5mm spark plug terminals feature Dual Crimp terminals. As the name implies, the terminals feature two crimps; one for the sleeve of the wire and another separate crimp to grasp the conductor. The MSD's 8.5mm spark plug terminals feature Dual Crimp terminals. As the name implies, the terminals feature two crimps; one for the sleeve of the wire and another separate crimp to grasp the conductor.

MSD Super Conductor 8.5 MM 2 In 1 Universal Spark Plug Wire Set

Sets include terminals for engines with early type (socket) and late type (HEI "spark plug top") distributor caps. Multi-angle plug boots and terminals are factory installed on one end.

Super Conductor 8.5 MM Spark Plug Wire has extremely low resistance and high RFI (radio frequency interference) suppression; a combination which would seem to defy the laws of physics. The low resistance is achieved through use of a helically wrapped, copper alloy conductor which is then wrapped around a ferro-magnetic impregnated center core.

This 2 in 1 universal wire set include terminals for engines with early type (socket) and late type (HEI"spark plug top") distributor caps. Straight plug boots and terminals are factory installed on one end. Extra Long cables you cut to length. Install included Distributor cap ends yourself. Includes both socket and spark plug style ends. Mini Wire Stripper and crimper included.

MSD 8.5 MM 2 in 1 Universal Spark Plug Wire Set - 90 Degree

This 2 in 1 universal wire set include terminals for engines with early type (socket) and late type (HEI"spark plug top") distributor caps. 90º plug boots and terminals are factory installed on one end. Extra Long cables you cut to length. Install included Distributor cap ends yourself. Includes both socket and spark plug style ends. Mini Wire Stripper and crimper included.

8mm 115 Deg Plug Boot Wire Set

• Two current paths for reliability and redundancy.
  • Primary path: Spiral wound stainless steel alloy.
  • Secondary path: Carbon impregnated fiberglass center core.
• Low 500 ohm per foot resistance.
• 8mm Silicone jacket to resist high temperatures, moisture, oil and chemicals.
• EPDM (Ethylene Propylene Diene Methylene) inner insulation for superior heat resistance and prevention of arcing and voltage leaks.
• Fiberglass reinforcing braid for added strength and flexibility.

8mm 90 Degree Plug Boot Wire Set

Two current paths for reliability and redundancy.
• Primary path: Spiral wound stainless steel alloy.
• Secondary path: Carbon impregnated fiberglass center core.
• Low 500 ohm per foot resistance.
• 8mm Silicone jacket to resist high temperatures, moisture, oil and chemicals.
• EPDM (Ethylene Propylene Diene Methylene) inner insulation for superior heat resistance and prevention of arcing and voltage leaks.
• Fiberglass reinforcing braid for added strength and flexibility.

8mm Straight Plug Boot Wire Set

• Two current paths for reliability and redundancy.
  • Primary path: Spiral wound stainless steel alloy.
  • Secondary path: Carbon impregnated fiberglass center core.
• Low 500 ohm per foot resistance.
• 8mm Silicone jacket to resist high temperatures, moisture, oil and chemicals.
• EPDM (Ethylene Propylene Diene Methylene) inner insulation for superior heat resistance and prevention of arcing and voltage leaks.
• Fiberglass reinforcing braid for added strength and flexibility.

• Johnson/Evinrude/BRP
• E-TEC Grounded Outboards
• 2005-2007
• 40HP-90HP
• 7MM Hi-Temp Silicone Suppression Wire
• 8 or 10 inch versions
• Ruggedized construction using thermo sealed heat shrink to prevent corrosion - Out performs OEM
• Hi-Temp Silicone boots for improved heat resistance
• Stainless Steel terminals, wire and plated components used throughout for improved corrosion resistance
• Provides RFI, EFI and Heat protection that exceeds OEM in E-TEC Grounded Outboard applications
• Application coverage for the full range of Generation 1 E-TEC outboards- 40-250 HP
• Replaces OEM # 5007636 - Superseding # 5006759 & 5006531, and # 5007415-Superseding # 5006210 & 5007114

Black Pro Spark Plug Wire Separators

Pro-series wire separators are constructed from high temperature ABS to be both oil and fuel resistant while providing the ultimateprotection against harmful ignition crossfire. Each separator bolts together for a positive clamp fit. Each set consists of two each 4 wire, 3wire and 2 wire separators. Fits 7mm to 8mm wires.