Hardin Marine

Used with three pins connectors to crimp everything together.

These showers distribute a continuous supply of water onto the upper section of the Bravo stern drive. Tests have continuously shown that the added cooling from the drive shower can double the service life and nearly double the bearing life of the out drive.

• Fits Alpha One, Alpha One Gen Two, Bravo One, Two and Three.
• Comes with full color illustrated installation instructions.
• Pick-up ports are adjustable up to 1-1/2 inches.
• With Mayfair Performance Shower/Cooler design you get more water flow and lower drive oil temperature.
• 3 times the water flow than other very popular shower cap designs.
• Has a 15-35 degree lower drive oil temp. Guaranteed or full refund.
• Available in Satin only.

• Custom designed crossover kit.
• Allows the use of a thermostat or a kit with no thermostat.
• Thermostat Housing has port for sender if desired

• 1" NPT Dual Inlet
• For Use with 1 or 2 Stage Sea Pump
• Includes #625-4382 high flow water inlet crossover in a dual inlet configuration.
• Extreme Series Power Steering Pump.
• Steering pump uses a short V-belt that is run off of a custom designed 2-groove sea pump pulley.
• Kit includes: a power steering pump, crossover with power steering mount, a dual groove sea pump pulley, the V-belt and mounting hardware.

• 1-1/4" Single Inlet Crossover Power Steering System.
• For Use with 1 or 2 Stage Sea Pump
• Includes #625-4372 high flow water inlet crossover in a dual inlet configuration.
• Extreme Series Power Steering Pump.
• Steering pump uses a short V-belt that is run off of a custom designed 2-groove sea pump pulley.
• Kit includes a power steering pump, crossover with power steering mount, a dual groove sea pump pulley, the V-belt and mounting hardware.

• Constructed of 316L Stainless Steel.
• 3/4" NPT outlet on the top of the crossover tube, for bypass.
• 1" NPT inlet.
• For BBC applications.
• Includes bolts and gaskets.

• Constructed of 316L Stainless Steel.
• 1" slip-on on the top of the crossover tube(can be used to bypass water to the thermostat housing).
• 1-1/4" slip-on connection inlet fitting.
• O-ring sealed, no gaskets required.
• Includes bolts.

Seaward Custom 8.2L Risers - Sold As A Pair, 11-3/8" tall

Limited stock available, custom height risers. If you are in the market for a Seaward 8.2L system talk to a salesman to see if these fit your application, as it may have considerable cost reductions over building new risers.

Custom Aluminum Fabricated Left Foot Rest Only

3-1/2" center to center on mounting holes, 13" overall length, 5-1/2" wide

Custom Aluminum Fabricated Right Foot Rest Only

If you are looking for something a little different and need a custom tip, then we have your answer! These popular angled end tips share the same great construction and gleaming finish as our standard tip but are custom made to various length styles and can accommodate reducers and angled flanges. These tips include flaps and will accept our popular slip-in silencers. Sold Each.

NOTICE: TWO OF THE CUSTOM CONFIGURATIONS ON HERE ARE NORMAL PRODUCTION ITEMS AVAILABLE AT LOWER COST AND SHOULD NOT BE ORDERED FROM THIS PAGE:

IF YOU DO NOT SEE THE OPTIONS YOU NEED IN THE DROP DOWN MENUS BELOW CONTACT US AND PROVIDE A SKETCH OF WHAT YOU ARE LOOKING FOR AND WE WILL PROVIDE A QUOTE!

CUSTOM TIPS TAKE 7-10 BUSINESS DAYS TO BUILD AND ARE QUOTE ONLY.

CUSTOM TIPS TAKE 7-10 BUSINESS DAYS TO BUILD AND ARE QUOTE ONLY.

Custom Dry Tailpipes for Keith Eickert Cast Aluminum Headers (Pair)

Note: This is a custom product, pricing published on the web is only used as a minimum guideline. Depending upon the length and number of bends your custom tailpipes require, the actual price may be significantly higher. You will be quoted the actual cost of your tailpipes after we receive your custom dimensions.

1" NPT X 1-1/4" Hose Extra Long 90° Custom Handcrafted Stainless Steel Fitting

We Offer the most complete line of chrome plated brass and custom fabricated stainless steel fittings available anywhere.  All of these fittings are sure to simplify your plumbing job and add a tasteful finishing touch. Measures 4" Long.

NOTE: This fitting is custom built to order and has a 7-10 day lead time before shipping

Custom Handcrafted 316L Stainless Steel Fitting
1-1/2" NPT To 1-1/2" Hose Straight

We Offer the most complete line of chrome plated brass and custom fabricated stainless steel fittings available anywhere.  All of these fittings are sure to simplify your plumbing job and add a tasteful finishing touch.

1-1/2" NPT X 1-1/2" Hose 90° Custom Handcrafted Stainless Steel Fitting

We Offer the most complete line of chrome plated brass and custom fabricated stainless steel fittings available anywhere.  All of these fittings are sure to simplify your plumbing job and add a tasteful finishing touch.

1-1/2" NPT X 1-1/2" Hose 90° Custom Handcrafted Stainless Steel Fitting

• Available: (4) Four
• Condition: Overstock

We Offer the most complete line of chrome plated brass and custom fabricated stainless steel fittings available anywhere.  All of these fittings are sure to simplify your plumbing job and add a tasteful finishing touch.

1-1/4" NPT X 1-1/2" Hose 90° Custom Handcrafted Stainless Steel Fitting

We Offer the most complete line of chrome plated brass and custom fabricated stainless steel fittings available anywhere.  All of these fittings are sure to simplify your plumbing job and add a tasteful finishing touch.

1-1/4" NPT X 1-1/2" Hose Straight Custom Handcrafted Stainless Steel Fitting

We Offer the most complete line of chrome plated brass and custom fabricated stainless steel fittings available anywhere.  All of these fittings are sure to simplify your plumbing job and add a tasteful finishing touch.

Custom MerCruiser Style Engine Harness - This unit is a Mercury style engine plug with 6-ft of un-terminated wire extending from it for the do-it-yourself installer.

These wiring harnesses were designed for use in custom engine installations. If you've ever tried to use an original Mercury harness on a custom engine installation you know that all of the wires either aren't located where you need them, or they're the wrong length. And there's so many that end up not being used. We have stepped in to build both a custom harness and a do-it-yourself harness using a factory Mercury style engine plug. Don't suffer from a tangled spaghetti-wire nightmare. Both the custom and universal harnesses are engineered of the highest quality wire,connections, terminals, and components.

Note: Uses 14 AWG wire

1-1/4" NPT X 1-1/4" Hose 90° Custom Stainless Steel Fitting

We Offer the most complete line of chrome plated brass and custom fabricated stainless steel fittings available anywhere.  All of these fittings are sure to simplify your plumbing job and add a tasteful finishing touch.

1-1/4" NPT X 1-1/4" Hose Straight Custom Stainless Steel Fitting

We Offer the most complete line of chrome plated brass and custom fabricated stainless steel fittings available anywhere.  All of these fittings are sure to simplify your plumbing job and add a tasteful finishing touch.

Custom Steel 1/4" NPT Dipstick Kit

The design of many marine oil pans does not allow the use of a stock dipstick. These pans have bungs to accommodate a universal dipstick kit. This universal dipstick kit is for pans which have a 1/4" NPT oil level check fitting built into them. The long tube can be bent to provide easy access. Dipstick needs to be re-calibrated for each installation. Overall tube length is 21".

Comes with optional weld in bung for even wider array of installation methods.

Cyclone "BIG GUN" System For GM Big Block - Fully Polished

At last the Biggest and the Best System available for the ultimate in performance These systems use an actual 4" internal pipe with a massive 4-1/2" outer shell These systems produce almost non-existent restriction to exhaust flow through the double wall water jacketed transom tail section These systems are referenced as dry tailpipe due to the fact exhaust flow never makes contact with the discharged water Each of these systems are designed for large cubic inch high horsepower and supercharged applications Additional transom sealing rings will need to be purchased separately When only the best will do Cyclone delivers Note: all Big Gun riser/tailpipes are custom built, a simple measurement guide is all that's needed to complete Allow 7-14 working days to build.

If you are one of thousands of performance boaters seeking the power and styling from stainless steel tubular headers then you're looking at the leader in exhaust technology. These "Cyclone" header systems share 100% 316L stainless steel construction. All appropriate flanges are laser cut and CNC machined for a perfect gasket seal. Each individual exhaust tube is bent to precise, exact tolerances every time. A computer designed fully welded water inlet manifold provides equal water distribution to each exhaust runner tube. While each set of headers goes through a 1900 degree annealing process that multiplies the durability factor of the header many times over while providing added protection against corrosion. But the heart of these systems lies in the ability to generate loads of additional power. By using CAD-5 Technology to develop a unique staggered tube runner length, these systems are capable of maximizing the broadest low end and mid range torque, all the while yielding incredible peak power gains. These systems are available in many configurations to fit every boaters needs. Rest assured when you lay down your hard earned money because the system comes complete with all necessary mounting bolts and gaskets making installation a snap.

Additional Information:

• Standard Mercury Exhaust Hole Locations
• How To Measure For Custom Tailpipes

Note:  Pricing indicated includes STANDARD DIMENSION Tailpipes only.  Custom Tailpipes may incur additional charges depending on the length and complexity of the tailpipe required.