Hardin Marine

Xtreme Remote Horizontal Rear Port Cylinder Head Mount HP4 or HP6 Oil Filter Head
New: Now With Engine Lifting Eye

The feature that sets this remote mount oil filter apart from the competition is the variety of mounting locations made available by using different mounting brackets Normally mounted horizontally on the rear of the port cylinder head this remote oil filter mount can also be mounted vertically on the front of the port cylinder head or remotely mounted vertically on a nearby bulkhead. Incorporating a large single 3/4" NPT inlet port and dual 3/4" NPT outlet ports the oil lines can be run straight thru or 90 degrees from each other There is also an 1/8" NPT port in the filter head that can be used as a oil pressure gauge access point of plugged if it's not needed Constructed for 316L Stainless Steel and polished to a mirror finish the construction and appearance of this assembly top notch just like all of the Hardin Marine product line.

Remote Reservoir Hose Kit

Includes Fittings

Xtreme Remote Vertical Bulkhead Mount HP4 or HP6 Oil Filter Head - Black

The feature that sets this remote mount oil filter apart from the competition is the variety of mounting locations made available by using different mounting brackets Normally mounted horizontally on the rear of the port cylinder head this remote oil filter mount can also be mounted vertically on the front of the port cylinder head or remotely mounted vertically on a nearby bulkhead. Incorporating a large single 3/4" NPT inlet port and dual 3/4" NPT outlet ports the oil lines can be run straight thru or 90 degrees from each other There is also an 1/8" NPT port in the filter head that can be used as a oil pressure gauge access point of plugged if it's not needed Constructed for 316L Stainless Steel and polished to a mirror finish the construction and appearance of this assembly top notch just like all of the Hardin Marine product line.

Xtreme Remote Vertical Bulkhead Mount HP4 or HP6 Oil Filter Head - Polished

The feature that sets this remote mount oil filter apart from the competition is the variety of mounting locations made available by using different mounting brackets Normally mounted horizontally on the rear of the port cylinder head this remote oil filter mount can also be mounted vertically on the front of the port cylinder head or remotely mounted vertically on a nearby bulkhead. Incorporating a large single 3/4" NPT inlet port and dual 3/4" NPT outlet ports the oil lines can be run straight thru or 90 degrees from each other There is also an 1/8" NPT port in the filter head that can be used as a oil pressure gauge access point of plugged if it's not needed Constructed for 316L Stainless Steel and polished to a mirror finish the construction and appearance of this assembly top notch just like all of the Hardin Marine product line.

Replacement 1/2" Stud for Hardin Generation 2 Offshore Sea Strainers

Designed to fit Hardin Offshore Generation 2 (420-913222) Sea Strainers only.

Replacement 1/2" Washer for Hardin Generation 2 Offshore Sea Strainer - 1/2" Shaft

Designed to fit Hardin Offshore Generation 2 (420-913222) Sea Strainers only.

Replacement Bilge Drain Flapper Kit

For use with 125-57505 J-Drain kit.

1-3/4" Square Dimension

Replacement Bottom O-Ring for Hardin Sand Strainer

Designed to fit Hardin Sand Strainers only.

Replacement Bracket for Oil / Fuel Filter, Power Steering Reservoirs and Sand Strainers - Polished

This Bracket is designed to replace a number of Hardin Marine products, including fuel filters, power steering reservoirs, oil filters and sand strainers.

Replace your worn out O-Rings in your Brazilian Manifold with the ones in this kit!

Burn Down Valve Cover Breather Gasket (Each)

Replacement Gasket for Burn Down Breather

• 3.875" bolt spread.
• 1.75" base width.
  

Replacement Cable Connection Kit for Stringer Mount Foot Control 

This kit replaces worn out cable connection hardware for Stringer Mount Foot Throttle 620-60214.
DOES NOT work with Floor Mount version.

Replacement Cap For MSD Distributor

MSD molds our most popular V8 distributor caps in-house. These caps are injection molded from DuPont® Rynite material and feature spark plug-style terminals. These terminals offer improved locking connections and the Rynite material is extremely strong with excellent dielectric properties. This cap comes with an optional wire retainer to lock the wires in place.

• 7-3/4" tall.
• Fits 625-7660 Extreme SS Filter Head.
• 1"-12 thread
• 21 micron.

Replacement Coil Bracket - Polished

• 356T-6 Billet Aluminum construction.
• Designed for 755-3555 and 755-3560

Replacement Cotter Pin for Hardin Generation 2 Offshore Sea Strainer - 1/2" Shaft

Designed to fit Hardin Offshore Generation 2 (420-913222) Sea Strainers only.

This kit contains the fittings and bolts to install a pair of manifolds on a big block Chevy Cyclone exhaust system.

This kit contains the fittings, gaskets and bolts to install a single riser on a big block Chevy Cyclone exhaust system.

Replacement Exhaust Manifold Adapter Bolt Covers - Pack of 16

This package of replacement covers will help you replace lost of missing ones. These covers are made from 6061-T6 billet aluminum. Sold in packs of 16.

Power Steering Filter Element for 137-9037

• Replacment filter element only.
  

Replacement Filter Only
for Intercooler Fine Mesh Sand & Sea Strainer

This unit uses a rugged and durable all stainless steel micron filter element to keep sand and small particles out while still allowing for maximum water flow.

• Replacement Fittings and Hose for Hardin/Gil Manifolds
• Kit does not come assembled.
• All Hardware 316L Stainless Steel

Replacement Fuel Pump Fitting -8 JIC to 5/8"-18

Replacement gasket for breather models 620-45756 and 620-45757.

• 7/16" Stud
• 4-3/4" Length

Used to mount Mayfair wing plates. SOLD EACH!