Generic

A: 7/16" , B: 4-3/4" , C: 3/4" , D: 11/16" , Break Strength: 4,400 lbs., Max Load: 1760 lbs.

"Features nominal wall thickness of 0.300". Resin meets FDA spec CFT177 1520 requirements. Satisfies all U.S. Coast Guard standards. Provides standard NPT openings for vent, fill & drain. Polyethylene tanks will not filter taste into water or emit waste odors."

Gals.: 4, Size: 11-3/4" L x 10-1/4" W x 9-1/4" H"

"Durable orange polyurethane. Will not mark or discolor boat. Cut and abrasion resistant. Will not "flat spot" even after months of storage. Roller is unaffected by grease, oil, gasoline, exhaust fumes, salt, etc. No bushings to pop out. Continuous bearings and reinforcing tubes on rollers over 7" long are completely enclosed in polyurethane. Shafts should be greased at installation."

Size: 4", Hole: 5/8", Reinforcing Tube: No, Case: 36

Sold: Each

Nickel Plated Brass. 12V, 180 mA

LEDs: 4, A: 1-1/2", B: 3/8", Watts: 20W, Candle Power: 700

Sold: Pack

6 LEDs. Nickel Plated Brass. 12V, 180 mA. All Around LED Festoon is for interior installations only.

LEDs: 4, A: 1-1/4", B: 3/8", Watts: 0.4, Case: 10

Sold: Each

Nickel Plated Brass. 12V, 180 mA

LEDs: 4, A: 1-1/4", B: 3/8", Watts: 20W, Candle Power: 700

Sold: Pack

"Hellamarine 3" round LED UV resistant courtesy lamps can be installed almost anywhere onboard. Advanced lens technology provides a cool, even spread of soft light while consuming less than .5W, a fraction of the energy of traditional bulbs. Each lamp is completely sealed, highly shock, impact and vibration resistant and run extremely cool for safer installations where the heat of an incandescent lamp may cause damage. Flush mount installations require a 2" cutout. Flush/Surface mount models include an adapter ring for surface mount applications."

Size: 3", Bezel: Chrome, LED Color: Blue, Mount: Flush, Volts: 12

Sold: Each

Hellamarine 3" round LED UV resistant courtesy lamps can be installed almost anywhere on board. Advanced lens technology provides a cool, even spread of soft light while consuming less than .5W, a fraction of the energy of traditional bulbs. Each lamp is completely sealed, highly shock, impact and vibration resistant and run extremely cool for safer installations where the heat of an incandescent lamp may cause damage. Flush mount installations require a 2" cutout. Flush/Surface mount models include an adapter ring for surface mount applications.

Size: 3", Bezel: Stainless, LED Color: White, Mount: Flush, Volts: 12

Durable rubber caps that protect connections against moisture and dirt. Corrosion resistant construction. Moisture repellent insulation. Brass contacts are polarized to assure proper mating of circuits.

Pins: 4, Pack: Retail

"4 Positions: Acc - Off - Ign/Acc - Ign/Start.
Brass case and mounting hardware. Chrome plated brass face nut. Brass mounting stem 13/16" - 24 x 1-7/32". Fits panels up through 1" thick. 4 brass screw terminals. Rating at 12V: 5A ignition, 5A start, 10A accessory."

Max Panel Thickness: 1'', Boot: No, Pkg.: Retail

Sold: Each

Ignition Switch 4 Position PL Screw w/Cap

The Seadog Four Position Ignition Switches have a polypropylene construction with a long shaft type.

• Color: Black
• Shaft diameter: 13/16"
• Maximum panel: 1-1/8"
• Terminal types: Screw
• with cap

"Can be used with all SeaStar systems except BayStar, Capilano and 3-line inboard systems. Includes 2 hoses. ID of 5/16". Not for use with SeaStar Pro systems."

Length: 4', Box: 2

Sold: Box

A double contact bayonet socket. Push switch with water resistant boot. Complete with 12 volt bulb. Chrome plated zinc. Screw size is 10 R.H., except for 0300DP2CHR which is 12 R.H.

Dia.: 5", Depth: 1-7/8", Volts: 12

Sold: Each

Tester plugs into connector of tow vehicle and illuminates when the electrical connections are correct. Tests to SAE standards on flat 4-way functions for tail light, stop/turn lights, and ground.

:

Sold: Each

4" Aluminum Heat Exchanger / Oil Cooler Cradle Mounting Clamp

• Stainless steel strap & bolt
• Mounting hole center to center is 5-1/4"

Size: 4", Fastener: #6

4" Clamp On Downturn Exhaust Mufflers Polished 316L (Sold as a Pair)

• Ease of installation
• High quality Stainless Steel construction
• OEM style transom mount
• Straight through design
• Utilizes water to dampen sound
• Designed and flow tested to ensure maximum flow
• Must be 3" to 4" below water line
• Clamp On, J2005 Sound Ordinance Approved

Application:
Universal

Continuous heavy duty blowers have a minimum life of 10,000 hours, making them ideal for general engine room or gen set enclosure ventilation. They are also well suited for general ventilation of head or galley areas and any application that requires regular extended operation. Rated at 250 CFM .

Flangemount, Hose: 4", Volts: 12, Size: 9-3/8" L x 8-3/4" W x 9" H 

Flexmount, Hose: 4", Volts: 12, Size: 9-1/4" L x 9-3/16" W x 9-5/8" H

97876 Crusader Heat Exchanger, 4" diameter, V6 262 CID, replaces older 3" diameter unit Crusader #97632.

Cummins Fuel Cooler Sen-Dure

16.93" OAL 4" diameter 2 1/2" hose connections