Generic

Dia.: 8", Height: 11-1/2", Color: Red, Eye: .6""

Description: Red Ball Knob Replacement

Replace most cut gaskets with a formed-in-place gasket. Use for valve covers, oil pans, timing covers, water pumps, etc. -75°F to +650°F intermittent. Sensor safe for engines equipped with oxygen sensors.

Size: 3 oz. tube, Case: 12

Sold: Each

Mounts on clean, flat surfaces using an industrial strength adhesive.

Lens: Red, Size: 3-1/8" x 1-3/8", Pack: 2, Case: 6

Sold: Pack

"Waterproof and constructed of extra tough polycarbonate to resist breakage. The light bulb is contained in a permanently sealed compartment and comes with a pre-installed 15" lead wire. Light may be used as a combination side marker and clearance light, when properly mounted (Note: Reflex reflector is not included)."

Lens: Red, Mount: Stud, White base, Size: 2-1/8" x 1-1/8" x 1-1/16"

Sold: Each

Double braid. A strong, flexible, and long wearing line. Great for a wide range of boats for Mainsheets, Jibsheets & Control lines. Durable and spliceable.

Size: 1/4" x 600', Color: White w/Red Fleck

Double braid. A strong, flexible, and long wearing line. Great for a wide range of boats for Mainsheets, Jibsheets & Control lines. Durable and spliceable.

Size: 3/16" x 600', Color: White w/Red Fleck

Double braid. A strong, flexible, and long wearing line. Great for a wide range of boats for Mainsheets, Jibsheets & Control lines. Durable and spliceable.

Size: 3/8" x 600', Color: White w/Red Fleck

These fittings are made of the same fiberglass and fire retardant resins used to make Vernatube. Fittings, couplings and elbows are lightweight, strong, non-corroding and durable.

OD: 3" to 4", Length: 10"

Sold: Each

Bronze and 90°. NOT TO BE USED IN POTABLE WATER SYSTEMS.

Size: 1-1/2" x 1"

Sold: Each

ID: 4 to 3.5", A: 3.5", B: 4", C: 4.5", D: 1.5", E: .25"

ID: 5 to 4.5", A: 4.5", B: 5", C: 5.5", D: 1.5", E: .25"

ID: 6 to 5", A: 5", B: 6", C: 6.5", D: 1.5", E: .25"

Reducing Nipple

Connector: Reducing Nipple, Replaces: 0, Thread: 1/8" x 1/4" NPT Hex", Hose: 0

Sold: Each

High-brightness, red & white reflective material is rated at 1,000 candlepower and features industrial-strength adhesive to mount on flat or curved surfaces. It also offers: four-times greater reflectivity, wider viewing angles, higher visibility at long range and tougher durability than conventional conspicuity reflectors.

Size: 2" W x 18" L", Pack: 4

Sold: Each

High-brightness, red & white reflective material is rated at 1,000 candlepower and features industrial-strength adhesive to mount on flat or curved surfaces. It also offers: four-times greater reflectivity, wider viewing angles, higher visibility at long range and tougher durability than conventional conspicuity reflectors.

Size: 2" W x 18" L", Pack: 8, Case: 12

Sold: Each

Key benefits:
• Keep drinks refrigerator-cold
• Maintains or reduces temperature of cold drinks
• Replaces most standard cup holders
• Holds bottles or cans
• Polished marine-quality 316 stainless-steel trim ring
• Two blue LED interior lights
• Mounts into surfaces of various thicknesses
• DC-powered premium thermoelectric Peltier cooling element
• Marine-tough
• Built-in drain
• Low-voltage cut off, high-heat cut off, and in-line fuse

This is a refrigerated cup holder that can be installed in any convenient location to keep drinks refrigerator-cold (results may vary based on environmental conditions).

The Refrigerated Cup Holder makes your last sip even colder than your first. It allows boaters to keep a can, bottle or any appropriately sized beverage container chilled on even the hottest days—something that a typical cup holder or can koozie can’t begin to accomplish. Simply store your drink in the Refrigerated Cup Holder between sips.

Designed as a marine-tough open-top cylinder that replaces nearly any existing standard 4-inch (102 mm) cup holder, it is large enough to fit a 20-ounce (591 ml) water or soda bottle, and also accommodates a standard-size beer or soda can. A specially angled bottom insert keeps bottles or cans in constant physical contact with the sidewall cooling element.

Bolt: 3/8" , Shank: 6" , Thread: 3"

Bolt: 3/8" , Shank: 8" , Thread: 4"

Bolt: 1/2" , Shank: 6" , Thread: 3"