Mercury Marine Catalog - Tools & Accessories

Support Block 91-814812A1

Holds and supports the dial indicator for various measurements, used as a base for the dial indicator.

Tapered Insert Tool 91-43579

Installs the tapered insert retainer into the water inlet hose on all the Bravo and Blackhawk drive units. Made of steel.

Thread Chaser / Nut Installer Tool Mercruiser 91-73688

This tool will remove and re install Mercury 4" spanner nuts.

Timing Decal (Priced Each. Must be sold in quantities of 10) 91-8538831

Aids in troubleshooting ignition timing on three cylinder engines by determining the timing of individual cylinders.

Timing Tool 91-805747A2

Connects to the DLC on MEFI-1, MEFI-2 and MEFI-3 ECM models. Locks ECM in timing mode to set initial engine timing.

Supersedes: 91-747508

Supercedes: 91-805747A1

TKS Carburetor Mixture Adjusting Tool 91-866201

Adjusts idle mixture screw on TKS MerCarb.

Mercruiser Flywheel Cup Puller 91-895190

Used On: 8 (4-STROKE)(209cc), 9.9 (4-STROKE)(209cc)

Mercruiser Bearing Cup Tool 91-8M0030292

Used On: ZEUS 3000 HH
ZEUS 3000 IH
ZEUS 3000 JH

Tool Drill Fixture 91-828363A1

Aids in the mounting of the following Panel Mount Controls: Commander300, 3000 Classic, Commander 2000.

Supersedes: 91-96760, 91-96760A1

Supercedes: 91-96760, 91-96760A1

Mercruiser Tool Kit 91-8M0026034

Used On: 30 EFI (3 CYL.)(4-STROKE), 40 Carb (3 CYL.)(4-STROKE), 40 EFI (3 CYL.)(4-STROKE), 40 EFI (4 CYL.)(4-STROKE), 40 EFI (4 CYL.)(4-STROKE)(JET), 50 EFI (4 CYL.)(4-STROKE), 60 EFI (4 CYL.)(4-STROKE)

Mercruiser Tool Kit 91-803581001

Used On: 15 Carb(2CYL)(4-STROKE), 20 Carb(2CYL)(4-STROKE)

Mercruiser Bearing Cup Tool 91-8M0030457

Mercruiser Cam Timing Tool 91-879150021

Used On: CMD QSD 2.0 EI 115, CMD QSD 2.0 EI 130, CMD QSD 2.0 EI 150, CMD QSD 2.0 EI 170, CMD QSD 2.0 ES 130, CMD QSD 2.0 ES 150, CMD QSD 2.0 ES 170

Mercruiser Flywheel Tool 91-895472

Torque Wrench, lb-in. 91-66274

Sets torques from 9 to 150 lb-in; 3/8 in. drive.

Transom Cutout and Drill Fixture 91-43693A2

Use for cutting and drilling the boat transom for sterndrive installation.

Supercedes: 91-71024A2

Trim Pump Test Gauge Kit 91-52915A6

Use in various trim pump tests.

Supercedes: 91-52915A8, 91-52915A3

Trim Rod Guide Removal Tool 91-44487T1

Aids in the removal of the trim rod from the trim cylinders.

Supersedes: 91-44487A1

Supercedes: 91-44487A1

U-joint Adaptor 91-38756

Supports the yoke when disassembling U-joint on all the drive units.

Upper Drive Shaft Housing Seal Driver 91-817570T

Installs the seals in the Alpha One Gen II drive shaft housing.

Supercedes: 91-817570