Autometer

12V Battery Extender (1.5 amp)

The Battery Extender is designed to maximize the life of a serviceable 12-volt lead acid battery. This means a vehicle battery will not give the annual dead battery surprise when removed from storage. The Extender keeps your battery at full charge on a continuous basis. When a battery is not keep at full charge it becomes sulfated, which is the main reason for premature battery failure. The Battery Extender should be used to charge and maintain all starting and deep cycle batteries in storage or that do not receive daily use. The Extender is fully compatible with gelled electrolyte (gel-cell) batteries. It's superior circuitry automatically delivers the correct charge to compensate for cars that are equipped with computers that require a continuous battery power supply to maintain data memory. Quality built-in and assured with circuit burn-in, as well as computerized testing and inspection to ensure top quality and performance. Care in handling and occasional cleaning of the leads and housing will keep it looking like new, and give you many years of satisfaction. The Extender also comes with two different plug in lead sets. A set with ring terminals that installs permanently in your vehicle makes it easy to quickly plug the Extender in at any time. Also included is a lead set with battery clips for batteries not in use or in storage. Also, allows you to to maintain two batteries on a single Extender by running the batteries in parallel by hooking up a positive and negative lead from battery 1 to battery 2 and hooking the Extender to one of the batteries. The Battery Extender will keep both batteries maintained at a full charge.

1/8" NPT Female to 10mm x 1 Male Metric Adapter

Metric adapter for adapting oil pressure and temperature gauges

1/8" NPT Female to 12mm x 1.5 Male 

• For Adapting Oil Pressure/Temperature Gauges
• Works On Many Foreign/Domestic Engines

1/8" NPT Female to 12mm x 1.75 Male

• For Adapting Oil Pressure/Temperature Gauges
• Works On Many Foreign/Domestic Engines

1/8" NPT Female to 16mm x 1.5 Male 

• For Adapting Oil Pressure/Temperature Gauges
• Works On Many Foreign/Domestic Engines

1/8" NPT Weld-In Temperature Bung Adapter

AutoMeter's GM LS engine gauge installation kits feature specialized components to ease the installation of an LS engine into your boat. Includes a full color installation guide that not only details the use of the included metric adapter fittings, short depth temperature sensor, and tachometer resistor, but also covers installation procedures for other commonly monitored parameters.

 Each kit includes:

• 12mm x 1.5 to 1/8 in. NPT adapter 
• 16mm x 1.5 to 1/8 in. NPT adapter 
• Low profile electric temperature sender
• 10K 1/2 watt resistor (tach function)

1/8'' Diameter Nylon Tubing, 10-Feet Long

Only for mechanical pressure gauges.

1/8'' Diameter Nylon Tubing, 12-Feet Long

• For Mechanical Pressure Gauges
• Not For Fuel Or Brake Pressure Gauges

1/8" Diameter Nylon Tubing, 10-Feet Long with Ferrules

Only for mechanical pressure gauges up to 200 psi (Except fuel pressure gauges).

#4 Braided Stainless Steel Hose, 3-Feet Long, 3/16'' ID Fittings

• For Mechanical Pressure Gauge
• Braided Stainless Steel Hose

#4 Braided Stainless Steel Hose, 4-Feet Long, 3/16'' ID Fittings

• For Mechanical Pressure Gauge
• Braided Stainless Steel Hose

#4 Braided Stainless Steel Hose, 6-Feet Long, 3/16'' ID Fittings

• For Mechanical Pressure Gauge
• Braided Stainless Steel Hose

#3 Braided Stainless Steel Hose, 3-Feet Long, 3/16" ID Fittings

• For Mechanical Pressure Gauge
• Braided Stainless Steel Hose

#3 Braided Stainless Steel Hose, 4-Feet Long, 3/16" ID Fittings

• For Mechanical Pressure Gauge
• Braided Stainless Steel Hose

#3 Braided Stainless Steel Hose, 6-Feet Long, 3/16" ID Fittings

• For Mechanical Pressure Gauge
• Braided Stainless Steel Hose