Bluewater Enterprises

Half Toggle Switch Boots - Black - 10 Pack 

These weather tight rubber moisture seal boots offer protection and styling for virtually any dash assembly while leaving the metal toggle exposed. 15/32" - 32 Threads

Used with NMEA 2000 systems and connectors. Available from 0.5 meter (1.6 ft.) to 10 Meter (32.8 ft.) Lengths. Drop cables are smaller in diameter than backbone cables and more flexible allowing easier connections and installations. The blue connectors correspond to other Bluewater brand NMEA 2000 connectors for a simple color coded installation. Note: Inch measurements shown below are rounded to the whole inch.

BlueWater's NMEA 2000 1/2 Meter Strip Cable comes with blue couplers on the Female end. This strip cable is easily connectible to other NMEA 2000 products, and has exposed conductors for easy wiring. The blue connectors correspond to other Bluewater brand NMEA 2000 connectors for a simple color coded installation.

The BlueWater NMEA 2000 Power Cable and Tee is used to connect a NMEA 2000 network to a power connection. This Power Cable and Tee comes in black, with blue couplers.

The NMEA 2000 right angle drop cable is designed to save space and simplify installations in tight or crowded areas. With a 90-degree molded 5-pin connector on one end, this cable provides a clean, low-profile connection to your NMEA 2000 network without putting strain on the cable or connector housing.

Perfect for behind panels, consoles, or other limited-access points, this right angle cable maintains full NMEA 2000 compatibility and ensures reliable communication between networked marine electronics. This nmea 2000 drop cable is engineered for durability, resisting saltwater corrosion, UV exposure, and mechanical wear.

As a vital part of your marine electronics setup, the nmea 2000 cable offers flexible lengths and easy installation, making it a top choice for space-conscious vessel owners.

Used with NMEA 2000 systems and connectors. Available in one, two, three and four connector fittings. The blue connectors correspond to other Bluewater brand NMEA 2000 connectors for a simple color coded installation. The two, three and four way tee connectors allow for multiple drop cables to be connected without the use of additional backbone cables.

NMEA 2000 Terminators allow for proper termination of an NMEA 2000 network. The blue connectors correspond to other Bluewater brand NMEA 2000 connectors for a simple color coded installation. One male and one female terminator is required for each NMEA 2000 network.

NMEA 2000 Terminators allow for proper termination of an NMEA 2000 network. The blue connectors correspond to other Bluewater brand NMEA 2000 connectors for a simple color coded installation. One male and one female terminator is required for each NMEA 2000 network.

Includes all components needed to create a dual device NMEA 2000 network. Kit includes a 2 meter power cable with tee, male and female terminators (1 each), one two way tee connector, and two 2 meter drop cables.

Includes all components needed to create a single device NMEA 2000 network. Kit includes a 2 meter power cable with tee, male and female terminators (1 each), one single tee connector, and one 2 meter drop cable.

• Custom Laser Etched Logos available
  
• 0.695" O.D.
• For 22mm 2 in 1 switches only

The latest in LED lit electronic switches from Bluewater Enterprises. These switches feature easily swappable buttons so you change functions easily. This version is sold without a wire harness for users who want to build their own wiring harnesses. See related parts. There are over 100 Switch Function Icons to choose from.

• 15 AMP Rating
• Multiple Switch Options
• 100 + Label Options
• Laser Etched Logos available
• IP69K Waterproof Rated
• 316 Stainless Steel Body
• Electronic Actuator
• Mechanically rated for 50,000 cycles
• Switches are LED Backlit
• WIRE HARNESS IS NOT INCLUDED!
• Caution: Momentary switch applications controlling solenoids may require a 5 amp diode on the output wire of the switch in order to prevent damage to the mosfet switch circuit.
• When using translucent buttons, labels are sold separately here.
• NOTE: Momentary Switch should not be used as an Engine Start switch

The latest in LED lit electronic switches from Bluewater Enterprises. These switches feature easily swappable buttons so you change functions easily. There are over 100 Switch Function Icons to choose from.

• 15 AMP Rating
• Multiple Switch Options
• 100 + Label Options
• Laser Etched Logos available
• IP69K Waterproof Rated
• 316 Stainless Steel Body
• Electronic Actuator
• Mechanically rated for 50,000 cycles
• Switches are LED Backlit
• Plug and Wire Harness with 12" wire lead INCLUDED.
• Caution: Momentary switch applications controlling solenoids may require a 5 amp diode on the output wire of the switch in order to prevent damage to the mosfet switch circuit.
• When using translucent buttons, labels are sold separately here.
• NOTE: Momentary Switch should not be used as an Engine Start switch

The latest in LED lit electronic switches from Bluewater Enterprises. These switches have built in breakers which can be set at positions from 0 to 20 Amps. These switches feature easily swappable buttons so you change functions easily. There are over 100 Switch Function Icons to choose from,  and for an extra touch, our 7/8" bezels fit these perfectly, see the related parts! The harness plug (sold separate) is easily removed for quick switch type changes and the connection is waterproof. The entire stainless steel switch body is threaded for use in dashes up to 1.5" thick.

• 20 AMP Rating (1 Channel), 10 AMP Rating (2 Channel)
• 8 programmable Amp positions: 3,5,6,7.5, 10, 15,20,0.
• Programmed by default at 5 Amp. We can factory reprogram for a small fee.
• Reprogramming only to be performed by authorized installers and dealers.
• Multiple Switch Options
• 100 + Label Options
• Switch button can be removed and replaced.
• 120A Inrush Surge Protection
• Laser Etched Logos available
• IP69K Waterproof Rated
• 316 Stainless Steel Body
• Electronic Actuator
• Mechanically rated for 50,000 cycles
• Switches are LED Backlit
• Plug and Wire Harness are NOT INCLUDED.
• Caution: Momentary switch applications controlling solenoids may require a 5 amp diode on the output wire of the switch in order to prevent damage to the mosfet switch circuit.
• NOTE: Momentary Switch should not be used as an Engine Start switch

The latest in LED lit electronic switches from Bluewater Enterprises. These switches have built in breakers which can be set at positions from 0 to 20 Amps. These switches feature easily swappable buttons so you change functions easily. There are over 100 Switch Function Icons to choose from,  and for an extra touch, our 7/8" bezels fit these perfectly, see the related parts! The harness plug is easily removed for quick switch type changes and the connection is waterproof. The entire stainless steel switch body is threaded for use in dashes up to 1.5" thick.

• 20 AMP Rating (1 Channel), 10 AMP Rating (2 Channel)
• 8 programmable Amp positions: 3,5,6,7.5, 10, 15,20,0.
• Programmed by default at 5 Amp. We can factory reprogram for a small fee.
• Reprogramming only to be performed by authorized installers and dealers.
• Multiple Switch Options
• 100 + Label Options
• Switch button can be removed and replaced.
• 120A Inrush Surge Protection
• Laser Etched Logos available
• IP69K Waterproof Rated
• 316 Stainless Steel Body
• Electronic Actuator
• Mechanically rated for 50,000 cycles
• Switches are LED Backlit
• Plug with wire connections is INCLUDED. No wire is included.
• Caution: Momentary switch applications controlling solenoids may require a 5 amp diode on the output wire of the switch in order to prevent damage to the mosfet switch circuit.
• NOTE: Momentary Switch should not be used as an Engine Start switch

The latest in LED lit electronic switches from Bluewater Enterprises. These switches have built in breakers which can be set at positions from 0 to 20 Amps. These switches feature easily swappable buttons so you change functions easily. There are over 100 Switch Function Icons to choose from,  and for an extra touch, our 7/8" bezels fit these perfectly, see the related parts! The harness plug is easily removed for quick switch type changes and the connection is waterproof. The entire stainless steel switch body is threaded for use in dashes up to 1.5" thick.

• 20 AMP Rating (1 Channel), 10 AMP Rating (2 Channel)
• 8 programmable Amp positions: 3,5,6,7.5, 10, 15,20,0.
• Programmed by default at 5 Amp. We can factory reprogram for a small fee.
• Reprogramming only to be performed by authorized installers and dealers.
• Multiple Switch Options
• 100 + Label Options
• Switch button can be removed and replaced.
• 120A Inrush Surge Protection
• Laser Etched Logos available
• IP69K Waterproof Rated
• 316 Stainless Steel Body
• Electronic Actuator
• Mechanically rated for 50,000 cycles
• Switches are LED Backlit
• Plug and Wire Harness with 12" wire lead INCLUDED.
• Caution: Momentary switch applications controlling solenoids may require a 5 amp diode on the output wire of the switch in order to prevent damage to the mosfet switch circuit.
• NOTE: Momentary Switch should not be used as an Engine Start switch

The latest in LED lit electronic switches from Bluewater Enterprises with adjustable breaker function. These switches feature easily swappable buttons (sold separately) so you change functions easily. This version is sold without a wire harness for users who want to build their own wiring harnesses. See related parts. There are over 100 Switch Function Icons to choose from,  and for an extra touch, our 7/8" bezels fit these perfectly, see the related parts!

• 20 AMP Rating (1 Channel), 10 AMP Rating (2 Channel)
• 8 programmable Amp positions: 3,5,6,7.5, 10, 15,20,0.
• Programmed by default at 5 Amp. We can factory reprogram for a small fee.
• Reprogramming only to be performed by authorized installers and dealers.
• Multiple Switch Options
• 100 + Label Options
• Switch button can be removed and replaced.
• 120A Inrush Surge Protection
• Laser Etched Logos available
• IP69K Waterproof Rated
• 316 Stainless Steel Body
• Electronic Actuator
• Mechanically rated for 50,000 cycles
• Switches are LED Backlit
• Caution: Momentary switch applications controlling solenoids may require a 5 amp diode on the output wire of the switch in order to prevent damage to the mosfet switch circuit.
• NOTE: Momentary Switch should not be used as an Engine Start switch
• WIRE HARNESS IS NOT INCLUDED!
  

The latest in LED lit electronic switches from Bluewater Enterprises. These switches feature easily swappable buttons (sold separately) so you change functions easily. This version is sold without a wire harness for users who want to build their own wiring harnesses. See related parts. There are over 100 Switch Function Icons to choose from,  and for an extra touch, our 7/8" bezels fit these perfectly, see the related parts!

• 120 AMP Rating (1 Channel), 10 AMP Rating (2 Channel)
• Multiple Switch Options
• 100 + Label Options
• 120A Inrush Surge Protection
• Transparent and Laser Etched Button Logos available separately
• IP69K Waterproof Rated
• 316 Stainless Steel Body
• Electronic Actuator
• Mechanically rated for 50,000 cycles
• Switches are LED Backlit
• WIRE HARNESS IS NOT INCLUDED!
• Caution: Momentary switch applications controlling solenoids may require a 5 amp diode on the output wire of the switch in order to prevent damage to the mosfet switch circuit.

The latest in LED lit electronic switches from Bluewater Enterprises. These switches feature easily swappable buttons so you change functions easily. This version is sold without a wire harness for users who want to build their own wiring harnesses. See related parts. There are over 100 Switch Function Icons to choose from,  and for an extra touch, our 7/8" bezels fit these perfectly, see the related parts!

• 20 AMP Rating (1 Channel), 10 AMP Rating (2 Channel)
• Multiple Switch Options
• 100 + Label Options
• Switch button can be removed and replaced.
• 120A Inrush Surge Protection
• Ultra Bright LED's
• Laser Etched Logos available
• IP69K Waterproof Rated
• 316 Stainless Steel Body
• Electronic Actuator
• Mechanically rated for 50,000 cycles
• Switches are LED Backlit
• Plug and Wire Harness ARE NOT INCLUDED.
• Caution: Momentary switch applications controlling solenoids may require a 5 amp diode on the output wire of the switch in order to prevent damage to the mosfet switch circuit.
• NOTE: Momentary Switch should not be used as an Engine Start switch
  

The latest in LED lit electronic switches from Bluewater Enterprises. These switches feature easily swappable buttons so you change functions easily. There are over 100 Switch Function Icons to choose from,  and for an extra touch, our 7/8" bezels fit these perfectly, see the related parts! The harness plug is easily removed for quick switch type changes and the connection is waterproof. The entire stainless steel switch body is threaded for use in dashes up to 1.5" thick.

• 20 AMP Rating (1 Channel), 10 AMP Rating (2 Channel)
• Multiple Switch Options
• 100 + Label Options
• Switch button can be removed and replaced.
• 120A Inrush Surge Protection
• Laser Etched Logos available
• Ultra Bright LED's
• IP69K Waterproof Rated
• 316 Stainless Steel Body
• Electronic Actuator
• Mechanically rated for 50,000 cycles
• Switches are LED Backlit
• Plug with wire connections is INCLUDED. No wire is included.
• Great choice for building a switch panel with your own wiring
• Caution: Momentary switch applications controlling solenoids may require a 5 amp diode on the output wire of the switch in order to prevent damage to the mosfet switch circuit.
• NOTE: Momentary Switch should not be used as an Engine Start switch