Bluewater Enterprises

These are easily swappable buttons so you change functions easily on 22mm Bluewater Switches with Removable Buttons. There are over 100 Switch Function Icons to choose from.

• 100 + Label Options
• Laser Etched Logos available
  
• When using translucent buttons, labels are sold separately here.
• 0.695" O.D.

These stainless steel switches can transform any dash by adding a touch of modern flair and is available in both a Standard On/Off contact or a Momentary On/Off contact version. The body design gives this button switch a waterproof rating of IP67. At night, every switch is backlit with blue LED light for unparalleled visibility. That light changes to red to let you know that function is on without question. The included wiring harness is clipped on. Labels are available to identify functions, see related parts.

6 Foot Flat Molding Strip For LED Light Strips

Blue LED Lighted Low Profile Push Button Switch

These switches are available in:
• Standard off/on
• Momentary on/off
• LED Light turns blue when activated, no light when off.
• 19 MM hole size.
• O.D. of Switch is 0.85 in
• 10 Amp
• Includes O-Ring 
• Wire Harness Included

Remote Dual Battery Switch

• Ignition protected - Safe for installation aboard gasoline powered boats
  
• Case design allows surface, front panel, or rear panel mounting
  
• Isolating cover with snap-on sections protects rear contacts
  
• 3/8"-16 tin-plated copper studs for maximum conductivity and corrosion resistance, accepts 3/8" and M10 ring terminals
  
• 7/8" (22.22mm) stud length to accept multiple cable terminals
  
• Ideal for marine or RV applications
  
• All non-corrosive marine grade metals
  
• Molded in durable reinforced polycarbonate
  
• Tactile textures indicate knob position by feel only
  
• Label with international ON/OFF legends
  
• Removable key or knob remains positively retained
  
• ICON label set included for circuit identification
• Same as Blue seas 6006 model

Remote Battery Selector Switch

• Ignition protected - Safe for installation aboard gasoline powered boats
  
• Case design allows surface, front panel, or rear panel mounting
  
• Isolating cover with snap-on sections protects rear contacts
  
• 3/8"-16 tin-plated copper studs for maximum conductivity and corrosion resistance, accepts 3/8" and M10 ring terminals
  
• 7/8" (22.22mm) stud length to accept multiple cable terminals
  
• Ideal for marine or RV applications
  
• All non-corrosive marine grade metals
  
• Molded in durable reinforced polycarbonate
  
• Tactile textures indicate knob position by feel only
  
• Label with international ON/OFF legends
  
• Removable key or knob remains positively retained
  
• ICON label set included for circuit identification

This heavy duty bus bar has 4 stud connections, 3/8"-16 thread.

Cover for the 4 Stud Busbar, see related parts

This panel mounted hi amp circuit breaker is available in 30 amps to 150 amps. Internal components are waterproof sealed. Switchable/Manual type.

This surface mounted hi amp circuit breaker is available in 30 amps to 150 amps. Internal components are waterproof sealed. Switchable/Manual type.

Remote Two Circuit Battery Selector Switch

• Ignition protected - Safe for installation aboard gasoline powered boats
  
• Case design allows surface, front panel, or rear panel mounting
  
• Isolating cover with snap-on sections protects rear contacts
  
• 3/8"-16 tin-plated copper studs for maximum conductivity and corrosion resistance, accepts 3/8" and M10 ring terminals
  
• 7/8" (22.22mm) stud length to accept multiple cable terminals
  
• Ideal for marine or RV applications
  
• All non-corrosive marine grade metals
  
• Molded in durable reinforced polycarbonate
  
• Tactile textures indicate knob position by feel only
  
• Label with international ON/OFF legends
  
• Removable key or knob remains positively retained
  
• ICON label set included for circuit identification

Relays and Bi-Stable relays such as a Remote Battery Switch or Charge Control Relay exhibit similar behavior as above only have low amperage requirements in some cases less than 250 milliamps not even 1 Ampere required by the device. But the bounce or magnitude of the resulting EFT (electrical fast transient) when being switched can be excessively high.

LED Lights, not all but some have internal power controllers. Others have basic switching drivers and have high noise or EFT (electrical fast transients) present while operating and when being switched on of a high magnitude and are expected; some are harsher than others. Could be very small LED’s or large spreader LED lights; either could have similar negative electronic behavioral effects. Again, even ones that consume less than 1 amp could be a significant contributor to faults.

None of the above has to do with the quality of a particular manufacturer it simply is an inherent characteristic of the referenced devices. However, there is a simple solution. Again, typically there is one switch or device when being turned on or operating that is attributing to In-Rush fault indication and easily identified. Typically, when being turned on or off however in the LED example it may not occur until after a long period of operation when voltage is depleted or temperature increases. In both examples B & C a 16V 1000uF electrolytic capacitor Part ID: 1406-000-001 can be installed across the Line V+ and Ground near the switch to correct the issue creating the fault.

This is a replacement plug with lead for the 516-9150-XXXX 19mm switches.

This tool allows you to crimp Deutsch connector pins to 14-24 AWG Wire

Dimmer Switch

This dimmer box will dim the LED light brightness for night operation

Double USB outputs 5VDC/2.1A, enough to charge iPhones, iPads and almost all other devices. Power Socket rated at 12 volts, 16 amps. Includes screws and connectors. Injection molded nylon.

A: " 3-1/2", B: " 1", C: " 1-5/8", Input: 12V-24V, Output: DC 5V/2.1A

Sold: Each

These dummy plugs are used in the switch Deutsch connectors when you are not using one of the wire holes.

Function Labels for 19MM Push Button Switches 

Identifying the function of each push button switch is simple with the interchangeable 3M adhesive backed actuator PU Dome Backlit Labels. These labels are used when using translucent actuator buttons that allows the LEDs in the switch body to pass light through the label. The result is excellent visibility at night. There are over 100 Switch Function Icons to choose from.

• Over 100 Interchangeable 3M Adhesive Backed PU Dome Backlit Function Icon Labels to choose from.
• Light passes through clear part of label
• Used with 19mm switches with the translucent label option