6061 Aluminum Flame Arrestor Spacer
Holley 4150 (5.10" I.D. x 7/8" Tall)

These spacers were developed to allow additional throttle linkage arm clearance for use with many aftermarket EFI Throttle bodies. The small spacer is standard equipment on Hardin marine 4150 series flame arrestors. 

ARP Cam Bolts - Ford 302/429/460

• 1968-Up Ford 302/429/460
• 1969-Up Ford 351W
• 1.580" UHL

In High Performance (170,000 psi) or Pro Series (200,000 psi), these quality ARP cam bolts deliver increased preload clamping force and assure positive timing gear register. With increased material strength, valve train harmonics and stress are overcome. The bolts also feature oversized head flange for button retention and reduced socket head size to facilitate easy installation and removal. Appropriate fasteners included for your application.

ARP Cam Bolts

• 1968-Up Ford 302/429/460
• 1969-Up Ford 351W
• 3/8-16
• 1.580" UHL

In High Performance (170,000 psi) or Pro Series (200,000 psi), these quality ARP cam bolts deliver increased preload clamping force and assure positive timing gear register. With increased material strength, valve train harmonics and stress are overcome. The bolts also feature oversized head flange for button retention and reduced socket head size to facilitate easy installation and removal. Appropriate fasteners included for your application.

Carburetor Linkage Bushing Set - Brass

The linkage bushing set allows the attachment of a 1/4" fastener to the 10/32" diameter hole found in the throttle linkage plate of Holley four barrel carbs. Split bushing design permits simple installation and eliminates the sloppiness present when rubber bushings are used.

12 volt 55 watt halogen bulb. Injection molded, fiberglass, nylon/stamped, 304 stainless steel. Sold individually.

Housing: Stainless Steel, A: 2-7/8", B: 2-11/16", C: 5-11/16"

Sold: Each

Exhaust Manifold Bolt Kit (per manifold) For 455 Olds Square Exhaust Manifold

Features include: Black graphics on a white face with chrome ring and a black pointer with fire-orange tip. Scratch resistant curved glass lense with polished stainless steel, near-flush bezel. white perimeter and red thru-dial lighting.

Size: 3", Type: Speedometer Kit, Pitot Type, Dial Range: 10-65 mph, Sender Code: 56973P Included

Sold: Each

"With a direct sight gauge or with the conversion capsule gathers fuel level information with the float. While accurate, the gauge will fluctuate as the fuel in the tank "sloshes" around the tank when boating because of the moving parts - the float. Direct site gauge is included with the sender."

Tank Depth: 14"

Sold: Each

NUT Mercruiser 11-803551001

Outboard Swivel Thru Hull Rigging Flange Kit - Fits 2" ID / 2.5" OD Hose

While the rest of the world is stuck in just one spot Hardin Marine has taken on the challenge to design the freedom of movement for your outboards rigging hose connection. With more movement than ever from today's popular outboard engines when being trimmed or stored for travel the industry has been faced with kinked rigging hoses and cowling damage due to the rigid hoes connection option that has only been available until now. This version fits 2" ID (2-1/2" OD) rigging hose.

Hardin's new  non-corrosive 2264 Delrin directional swivel hose connection provides 12 degrees of angle for hose/ tube movement and a water tight seal. With hidden non-exposed mounting hardware this unit features the ultimate in a clean smooth finish.

Attachment of the rigging hose couldn't be easier as the unit is threaded so that the rigging hose screws counter clockwise into the swivel ball connector requiring no additional hardware for hose attachment for the ultimate in finished appearance.

The 3/4" tall flange has a 5" diameter OEM factory mounting foot print. and requires a 3-3/8” hole to install with (4) #10 fasteners (NOT included). The Connector assembly measures 2-1/2" overall installed height.

This Multi angle rigging tube connector is available in a OEM black finish or with an optional polished or powdercoated Stainless Steel trim ring both individually or as a kit with rigging hose.

Kits include a Transom swivel connector and 5' long, 2" ID (2-1/2" OD) diameter premium corrugated black, gray or white rigging hose that is durable, flexible, and kink resistant to provide an excellent protection for cables and wiring from dirt, abrasion, sun and water. Our rigging hose is the hose of choice for most OEM boat builders.