High Performance Fuel Pump Upgrade For Raw Water Pump Mounted Fuel Pumps On Big Block Chevy Gen 5 & 6 Engines

By swapping our redesigned pump assembly on to your Gen 5 or Gen 6 fuel pump we can increase your fuel system to an estimated 120 GPH mechanical self-regulated pump at 6-8 PSI. This pump has -8 inlet and a -8 outlet. A perfect upgrade for supercharged engines.

This Is for Sea Pump Mounted Fuel Pumps

Marine Fuel Pump with Billet Base

KE Performance Products new fuel pump is based on the industry standard Carter mechanical marine vent style fuel pump but features a custom 6061-T6 billet aluminum intermediate and lower housing.  This pump is designed to offer greater reliability, increased strength/durability and more consistent fuel pressure and flow.  These pumps are self regulated at 6-8psi and also feature -8AN to #8 fittings with a special taper to maintain clearance as stock pumps.  Available to fit big block Chevrolet applications.

This Is A Block Mounted Fuel Pump

Clear Anodized Billet Manual Fuel Valve Assembly

At last a fuel valve you're not trying to hide. This clear anodized billet fuel valve is something everyone would be proud to own. 1/2 NPT Ports. It has left tank, right tank, both tanks, and off for setting. Measures 2-3/4" X 2-3/4" X 2-1/4" deep

Note: This valve is not USCG approved.

***APPLICATION WARNING: This valve is intended for use on the suction side of systems only (between tank and pump). Do not install on the pressure side of pumps or in pressurized lines where the valve would be subjected to positive pressure.***

5/8" Stainless Steel Straight Fuel Vent

These stainless steel fuel vents offer an almost completely flush finish leaving no protruding hardware. Each vent comes complete with nut and backing plate. This vent is perfect in harsh corrosive environments. Flange O.D. is 1.820".

5/8" Stainless Steel Right Angle Fuel Vent

These stainless steel fuel vents offer an almost completely flush finish leaving no protruding hardware. Each vent comes complete with nut and backing plate. This vent is perfect in harsh corrosive environments.

Fuel Pump Safety Switch

This fuel pump safety switch is designed to shut off your electric fuel pump when the engine oil pressure drops below 15 lbs.  It can easily be "Tee'd" into the oil pressure ending unit off the block.  Designed for 12Volt systems.

HP 500/525 Flow Command Fuel Pressure Regulator (Red Color)

Hardin Marine just introduced the MerCruiser HP500 Systems application to its line of high performance Flow Command adjustable fuel flow modifiers. The billet aluminum Flow Command is designed specifically for stock or modified HP500 systems. The Flow Command allows modification of the fuel flow rate to properly tune the air flow ratio. Ideal for use with high flow exhausts and intakes, the Flow Command incorporates these exclusive features:

• Bolt-on adjustable modifier for stock fuel regulators
• 6061-T billet aluminum case, CNC machined
• Allows pressure adjustments from 25 to 65 PSI
• Machined to exacting tolerances

Fuel Line Return To Tank Adapter - 2" O.D With 3/8" NPT Female Pipe Connection

These stainless steel fuel return adapters are perfect for an EFI conversion or any high output return style fuel system. These allow you to simply remove a small section of your 2" fuel fill hose and clamp the adapter in place - no welding required. 4" Long.

Fuel Pump Relay Kit

This Hardin Marine kit is intended primarily for those application running an electric fuel pump. The long wire runs in these kinds of installations can sometimes result in a voltage drop at the electric pump. Installation of this kit is good insurance that the fuel pump will be receiving full voltage from the battery.

Features:

• Can be used with any electric fuel pump, as long as the current load is not above 30 amps
• 30 amp relay is included with a relay socket wired with long leads specifically designed to reduce the number of splices required
• Quality insulated crimp connectors are provided to make the necessary splices, where required.

• Detailed instruction included

Xtreme Billet Aluminum / Stainless Steel Coalescing Fuel & Water Separator

Form and function is beautifully combined in these coalescing fuel and water separators Constructed of stainless steel and polished to a mirror finish these filter mounts offer a quad webbed bolt configuration that allows a straight-thru or 90 degree inlet to outlet fuel hose routing. The large 3/4" NPT ports provide for maximum fuel flow approaching 200 gallons per hour The high flow and high pressure capabilities and the 1/8" NPT fuel pressure sender port of this assembly make it perfect for both carbureted and fuel injected applications The unique "coalescing" element core is impervious to moisture and contamination and foreign particles while providing maximum fuel system flow.

• Bracket is Constructed of Polished 316L Stainless Steel. Head in Billet Aluminum
• Quad webbed bolt configuration allows a straight-thru or 90 degree inlet to outlet fuel hose routing.
• Three Large 3/4" NPT ports provide for maximum fuel flow approaching 200 GPH.
• 1/8" NPT fuel pressure sender port.
• Perfect for carbureted and fuel injected applications.
• 21 micron filter.

• 7-3/4" tall.
• Fits 625-7660 Extreme SS Filter Head.
• 1"-12 thread
• 21 micron.