Hardin Marine

Mercury 1075 Two Stage -16 ORB Dual Common Inlet/Outlet Sea Pump Adapter - Replaces Mercury #842625

These components are designed to assist in the plumbing of your engine when using the Hardin Marine Multi-Stage sea pumps. A wide range of configurations can be created by using different inlet and outlet adapters. All of these components are polished stainless steel or hard anodized to resist harsh corrosive environments. Replaces Mercury OEM # 842625

Non-Standard port side trim sender and mount

Mercury Control Adapter

Mercury Fuel Filter Replacement (RF51)

The RF51 spin-on Fuel Filter utilizes FST’s exclusive FloMax™ low restriction, high efficiency filter media that filters down to 4 microns, and strips 99% free water.

• 100% Made in America • Size: O.D.: 11/16” (93.7mm) Height: 3-7/8” (98.4mm)
• Thread: 11/16-16
• Gasket/Seal: (attached) O.D. 2.834(72mm) I.D.: 2.462 (63mm) Thick 0.500 (5mm)
• Flow: 200 gallons per hour
• Filtering Effificiency: 4 Microns: FloMax™ exclusive cellulose (gasoline-methanol-ethanol compatible). Most competitors are in the 10-24 Micron range.
• Water Separation: FST’s exclusive, enhanced cellulose FloMax™ filter media strips/ separates water to a “quiet” zone for water and heavy contaminates to settle. Strips 99% of free water. Not water blocking and does not swell up, which can block the fuel flow.
• Burst: 250 psi

Impeller Rebuild Service Kit - For Gen 4, Gen 5/6, Rev. 1 Hardin Stainless Pumps - Mercury Replacement

This impeller kit is a rebuild service kit for the Hardin Marine stainless impeller housing 625-4178 and stainless pumps 625-4110 and 625-4118 . This kit comes with new wear plates , O-rings, and impeller.

Which Rebuild kit do I need?

Rev. 1 pumps have a 1/8" drain plug in the rear housing and a slotted front wear plate.
Rev. 2 pumps have no drain plug and a solid front wear plate.

Mercury

This impeller kit is a rebuild service kit for the Hardin Marine stainless impeller housing 625-4178 . 

• (1)Impeller
• (2) Wear Plate
• O-rings

See here for individual replacement parts.

Mercury Outboard Adapter

Mercury Racing 525 EFI, 600/662/700 SCI Series V8 MLS Exhaust Gasket - Sold in Pairs

These gaskets are designed to withstand the highest of temperatures on high horsepower applications. For those of you looking to do the job only once insist on Hardin Marine extreme-duty gaskets. Quite possibly the last gasket you’ll ever need.

These MLS exhaust gaskets are ideal for both aluminum heads & cast iron heads as well as cast iron and aluminum blocks. The composition of MLS gaskets will also withstand the shearing forces created by aluminum heads on cast iron blocks. No re-torque is required and by design promotes an even torque load across the sealing surface.

Sold in Pairs

Mercury Racing 700 Intercooler Hi-Flow Fitting Kit

This fitting kit replaces the stock fittings with larger higher flow fittings allowing better cooling performance. Fittings are -10 AN.

Mercury Racing Fuel Filter Element (Replacement #35-8M0000202 or (RF500M)

The FST Performance RF500M fits the OEM Mercury racing filter head as well as the Hardin Marine Billet fuel / water separator head #625-7667. This filter removes contaminates down to as small as 3 Microns while separating water. With a flow rate of 5GPM and up to 300 GPH flow with less than 1% pressure drop at 75psi through 579 sq.in. of filter material.

Measurements: 6-1/2" tall and 3-5/8" wide. Thread size is 1"-14 

Mercury Sterndrive Cable Adapter

Adapts 33C / 3300 style cables for use with Mercury Engines.

Trim Sender Actuator for Mercury Verado applications.

Modular Terminal Block End Caps 5 Pack

Use with modular terminal blocks sold separately to complete your terminal block.

Modular Terminal Block Removal Tool

Use this tool to separate Modular Terminal Block sections.

Modular Terminal Blocks 5 Pack

These 30 Amp rated marine grade terminal blocks offer secure connections of the vital instrument wiring in your boat. Their modular nature allows you to build a terminal block of any size you need. Use with modular end caps sold separately to complete your terminal block.

This is a Momentary Trim Switch that will replace worn out switches on Early Hardin, Gaffrig and Livorsi controls.

• Fits Momo 6-Bolt Steering Wheels (All 6-bolt Wheels we sell are Momo)
• 3-1/2" Diameter 
• 3/8" Height
• Polished Billet Aluminum
• Includes 6 bolts for mounting 
• Can be used with most steering wheel adapters 
• Designed to be used with Hardin Marine One-Piece Adapters (see related items)

This module changes the direction of the motor, and dynamic breaking stops the motor when the switch returns to “OFF”. The low profile is perfect for tighter spaces and the hardware is completely corrosive resistant. It’s ideal for tarp or lift applications, as well as for hoists, hatches, winches, slowpows, intake/exhaust fans, vehicle outriggers, and other reversing applications.

Mounting Plate for 151-1200 Trim Switch

Plate and 4 screws for mounting a 151-1200 Trim Switch to most steering wheels.

MSD Bracket, Ford Front Cover Mount

• Ultimate in a clean and functional installation.
• Designed to sandwich between an MSD 6M, Max Volt MV-D6 or a Daytona Sensors CD-1 Control Box.
• Satin Finished Stainless Steel.
• Will mount on a 460 Ford Cylinder Head

• Dual Side Mount Shifter.
• Positive Locking feel when in hand.
• Ergonomically Designed.
• Uses two 33C cables.
• Can be used with factory Mercury cables with purchase of adapter sold separately.
• This is a Shifter only and is designed for use in conjunction with a foot throttle assembly