730-LEDPUBLWC LED Pop-up Bow Light Cup
For use with 730-LEDPUBL.
|
|
This Part has options, please click the button below to order.
730-TTK750 + Option(s) Livorsi 16"L X 12"W 750 Series Trim Tabs
-
Available in 11 powder coat colors and private labeling
-
Mil-Spec hard coat anodized topped with a powder coat finish to prevent corrosion
-
Models are available for performance boats, center consoles, cruisers, run-abouts, workboats and military boats
-
For use on boats 20 - 50 feet
-
Choose between LED electronic position indication (plug and play) or mechanical position indication (uses 33C cables)
-
Electronic models are compatible with NMEA 2000® compliant systems and Mercury VesselView®
-
The electronic IP68 sensor plugs directly to Livorsi's LED Position Indicator
-
Tabs are CNC machined from billet aluminum, no casting
-
Tabs are Mil-Spec hard coat anodized to prevent corrosion
-
Bolt patterns include Mercury and a smaller Livorsi bolt pattern for center consoles
-
All hinge pins and hardware are stainless steel
-
Adjustable transom angles without the use of special tools
-
Hydraulic cylinders are designed for 1500 PSI working pressure with dual seals
-
These cylinders may be serviced
-
Five anodes for complete saltwater protection
These kits Include:
- Two billet tabs
- Two pumps
- Mounting hardware
- Harnesses
- Thru hull fittings
- Stainless steel braided hoses and trim switches are purchased separately.
Four hoses are needed for one kit, two per cylinder.
|
|
This Part has options, please click the button below to order.
730-TTK850 + Option(s) Livorsi 13.5" wide x 15.5" long 850 Series Trim Tabs
-
Available in 11 powder coat colors and private labeling
-
Mil-Spec hard coat anodized topped with a powder coat finish to prevent corrosion
-
Models are available for performance boats, center consoles, cruisers, run-abouts, workboats and military boats
-
For use on boats 20 - 50 feet
-
Choose between LED electronic position indication (plug and play) or mechanical position indication (uses 33C cables)
-
Electronic models are compatible with NMEA 2000® compliant systems and Mercury VesselView®
-
The electronic IP68 sensor plugs directly to Livorsi's LED Position Indicator
-
Tabs are CNC machined from billet aluminum, no casting
-
Tabs are Mil-Spec hard coat anodized to prevent corrosion
- Livorsi bolt pattern for center consoles
-
All hinge pins and hardware are stainless steel
-
Adjustable transom angles without the use of special tools
-
Hydraulic cylinders are designed for 1500 PSI working pressure with dual seals
-
These cylinders may be serviced
-
Five anodes for complete saltwater protection
These kits Include:
- Two billet tabs
- Two pumps
- Mounting hardware
- Harnesses
- Thru hull fittings
- Stainless steel braided hoses and trim switches are purchased separately.
Four hoses are needed for one kit, two per cylinder.
|
|
This Part has options, please click the button below to order.
730-TTK950 + Option(s) Livorsi 14" wide (9.25" wide at end of tab) x 19" long 950 Series Trim Tabs
-
Available in 11 powder coat colors and private labeling
-
Mil-Spec hard coat anodized topped with a powder coat finish to prevent corrosion
-
Models are available for performance boats, center consoles, cruisers, run-abouts, workboats and military boats
-
For use on boats 20 - 50 feet
-
Choose between LED electronic position indication (plug and play) or mechanical position indication (uses 33C cables)
-
Electronic models are compatible with NMEA 2000® compliant systems and Mercury VesselView®
-
The electronic IP68 sensor plugs directly to Livorsi's LED Position Indicator
-
Tabs are CNC machined from billet aluminum, no casting
-
Tabs are Mil-Spec hard coat anodized to prevent corrosion
-
Bolt patterns include Mercury and a smaller Livorsi bolt pattern for center consoles
-
All hinge pins and hardware are stainless steel
-
Adjustable transom angles without the use of special tools
-
Hydraulic cylinders are designed for 1500 PSI working pressure with dual seals
-
These cylinders may be serviced
-
Five anodes for complete saltwater protection
These kits Include:
- Two billet tabs
- Two pumps
- Mounting hardware
- Harnesses
- Thru hull fittings
- Stainless steel braided hoses and trim switches are purchased separately.
Four hoses are needed for one kit, two per cylinder.
|
|
This Part has options, please click the button below to order.
730-TTK1050 + Option(s) Livorsi 21" X 10" 1050 Series Trim Tabs
-
Available in 11 powder coat colors and private labeling
-
Mil-Spec hard coat anodized topped with a powder coat finish to prevent corrosion
-
Models are available for performance boats, center consoles, cruisers, run-abouts, workboats and military boats
-
For use on boats 20 - 50 feet
-
Choose between LED electronic position indication (plug and play) or mechanical position indication (uses 33C cables)
-
Electronic models are compatible with NMEA 2000® compliant systems and Mercury VesselView®
-
The electronic IP68 sensor plugs directly to Livorsi's LED Position Indicator
-
Tabs are CNC machined from billet aluminum, no casting
-
Tabs are Mil-Spec hard coat anodized to prevent corrosion
-
Bolt patterns include Mercury and a smaller Livorsi bolt pattern for center consoles
-
All hinge pins and hardware are stainless steel
-
Adjustable transom angles without the use of special tools
-
Hydraulic cylinders are designed for 1500 PSI working pressure with dual seals
-
These cylinders may be serviced
-
Five anodes for complete saltwater protection
These kits Include:
- Two billet tabs
- Two pumps
- Mounting hardware
- Harnesses
- Thru hull fittings
- Stainless steel braided hoses and trim switches are purchased separately.
Four hoses are needed for one kit, two per cylinder.
|
|
This Part has options, please click the button below to order.
730-TB + Option(s) Livorsi Control Bezels
Powdercoated bezels for use with Livorsi Controls. 8-1/4" Long.
|
|
730-TST Replacement Transducer for Livorsi DFG series Depth Sounders. Works in either Shoot-Thru or Transom Mount applications. Includes epoxy for Shoot Thru mount. Only for use with Livorsi DFG series or equivalent Hawkeye D10D model Depth Sounders. This kit is the same at 730-TTR, it just includes epoxy, which the TTR kit does not.
|
|
This Part has options, please click the button below to order.
730-DC4000 + Option(s) Livorsi 3-3/8" Mega or Race Series 0-4000 RPM Diesel Tachometer with Plug-In Connectors
Livorsi Marine's brand new line of performance gauges featuring the new Mega& Race Rims with Plug-In Connectors. This new series is a whole new familyof gauges from 2" to 5" that you can mix & match to create a custom look.
Livorsi Marine gauges are now easier than ever to install! The Plug-Infeature on these instruments significantly decreases rigging time. Theplug-in connectors are waterproof and resist salt corrosion. Gauges areencased in all non-ferrous hardware. These gauges include state-of-the-artL.E.D. lighting, for easy viewing in low light conditions.
These gauges feature newly designed rims. The Mega rim has a boldstrong look, making your gauges standout. It has less height to the rim,giving it higher visibility from an angle, an important factor when operatingyour boat. The Race rim has a sleek look, that make your gauges standout.
Overall gauge width is 3-3/4" and dash cutout size is 3-3/8".
ALL LIVORSI GAUGES ARE MADE TO ORDER AND SHIP FROM THE FACTORY IN 2-3 WEEKS.
Need help measuring your gauges so you know what to look for when you finally upgrade to a more polished set? Check out this handy tutorial!
|
|
730-GPSESQ3 Convert your electronic automotive speedometer into a GPS speedometer with this GPS Pulse Antenna. The antenna receives GPS satellite signals and outputs the information to 8,000 or 16,000 pulse signal to your existing speedometer. This antenna eliminates connections to the transmission or the need to calibrate to your vehicles tire size. This fast update antenna receives signals 10Hz (10 per second) driving your speedometer to display your true speed (no pointer lag). This antenna is a stand alone device, which does not require a membership fee for GPS service. The antenna can be mounted under the dash or in an other hidden area as long as you verify the speedometer is working properly before permanently mounting the antenna. Accuracy and ease of installation makes this GPS Pulse Antenna an affordable solution if you are looking to upgrade to a GPS speedometer system.Convert your electronic automotive speedometer into a GPS speedometer with this GPS Pulse Antenna. The antenna receives GPS satellite signals and outputs the information to 8,000 or 16,000 pulse signal to your existing speedometer. This antenna eliminates connections to the transmission or the need to calibrate to your vehicles tire size. This fast update antenna receives signals 10Hz (10 per second) driving your speedometer to display your true speed (no pointer lag). This antenna is a stand alone device, which does not require a membership fee for GPS service. The antenna can be mounted under the dash or in an other hidden area as long as you verify the speedometer is working properly before permanently mounting the antenna. Accuracy and ease of installation makes this GPS Pulse Antenna an affordable solution if you are looking to upgrade to a GPS speedometer system.
|
|
730-GPSSQ3 Standard 1-second 1 HZ update with 4 ft harness and ring terminals,2 3/4" L x 2 3/8" W x 7/8" H. This receiver is used on Livorsi GPS gauges made prior to July 2015.
|
|
730-GPSSQ310X For use with the Livorsi GPS Speedometer with Odometer and Standard Livorsi GPS Gauges without Odometer made after July 2015. For Standard GPS Gauges without Odometer Made before July 2015 order 730-GPSSQ3 Fast 10 Hz 10x update with 4 ft harness with ring terminals, 2 3/4" L x 2 3/8" W x 7/8" H
|
|
730-GPSRAQ3VV Recommended for use with Livorsi Vantage View® Speedometers. Standard 1-second 1HZ update with 4 ft harness. Power and ground are pre-terminated and the signal wire is pre-terminated with a butt connector to connect to the NMEA 0183 input on the Master Harness. 2 3/4" L x 2 3/8" W x 7/8" H
|
|
730-GPSRAQ3VV Recommended for use with Livorsi Vantage View® Speedometers. Standard 1-second 1HZ update with 4 ft harness. Power and ground are pre-terminated and the signal wire is pre-terminated with a butt connector to connect to the NMEA 0183 input on the Master Harness. 2 3/4" L x 2 3/8" W x 7/8" H
|
|
This Part has options, please click the button below to order.
730-402 + Option(s) Livorsi Industrial Series Dual Engine Nine Gauge Kits
We've decided to take some of the guess work our of your next gauge set purchase. By combining the nine most popular gauges we are able to offer you the very best gauges at the very best value. The industrial series gauges are only available in the Standard size. The Industrial Series is characterized by the SAE Rim. Industrial Gauges are only available in Standard Sizes
Gauge sets include:
- (2) 3-3/8" 6000 RPM Tachometer
- (2) 2-1/16" Oil Pressure
- (2) 2-1/16" Water Temperature
- (1) 2-1/16" Fuel Level
- (2) 2-1/16" Voltmeter
Note: Plug-In Connectors are sold separately.
ALL LIVORSI GAUGES ARE MADE TO ORDER AND SHIP FROM THE FACTORY IN 2-3 WEEKS.
These gauges are available with a WHITE or BLACK face, and WHITE, BLACK or STAINLESS STEEL rims.
Need help measuring your gauges so you know what to look for when you finally upgrade to a more polished set? Check out this handy tutorial!
|
|
This Part has options, please click the button below to order.
730-GPSS + Option(s) Industrial Series GPS Speedometer Gauge 3-3/8"
The Livorsi Industrial Series Gauges have a bold and classic look.
- GPS satellite guided analog speedometer
- Provides accuracy with no needle bounce
- No pitot tube needed
- Memory recall retains highest speed
- Accurate readings on stepped or ventilated bottoms
- Connects to the output of some GPS antenna/receivers
- Available in 3 3/8"
- Choose gauge/harness only or full kit
- Kits include speedometer, compact antenna/receiver, memory recall and harness
- Click here to see a comparison on rim types
- Overall gauge width is 3-3/4" and dash cutout size is 3-3/8"
Need help measuring your gauges so you know what to look for when you finally upgrade to a more polished set? Check out this handy tutorial!
|
|
This Part has options, please click the button below to order.
730-400 + Option(s) Livorsi Industrial Series Single Engine Five Gauge Kits
We've decided to take some of the guesswork out of your next gauge set purchase. By combining the five most popular gauges we are able to offer you the very best gauges at the very best value. The industrial series gauges are only available in the Standard size. The Industrial Series is characterized by the SAE Rim. Industrial Gauges are only available in Standard Sizes
Gauge sets include:
- 3-3/8" 6000 RPM Tachometer
- 2-1/16" Oil Pressure
- 2-1/16" Water Temperature
- 2-1/16" Fuel Level
- 2-1/16" Voltmeter
Note: Plug-In Connectors are sold separately.
ALL LIVORSI GAUGES ARE MADE TO ORDER AND SHIP FROM THE FACTORY IN 2-3 WEEKS.
These gauges are available with a WHITE or BLACK face, and WHITE, BLACK or STAINLESS STEEL rims.
Need help measuring your gauges so you know what to look for when you finally upgrade to a more polished set? Check out this handy tutorial!
|
|
This Part has options, please click the button below to order.
730- + Option(s) Livorsi Monster Size Dual Inboard Engines Nine Gauge Kit
We've decided to take some of the guess work our of your next gauge set purchase. By combining the nine most popular gauges we are able to offer you the very best gauges at the very best value.
Monster Dual Gauge sets include:
- (2) 4-5/8" 6000 or 8000 RPM Tachometer
- (2) 2-5/8" Oil Pressure
- (2) 2-5/8" Water Temperature
- (1) 2-5/8" Fuel Level
- (2) 2-5/8" Voltmeter
Note: Plug-In Connectors are sold separately.
ALL LIVORSI GAUGES ARE MADE TO ORDER AND SHIP FROM THE FACTORY IN 2-3 WEEKS.
Livorsi Gauges are available in many color combinations, please select the Rim Style, Rim Color, Face Color and Tach RPM.
Need help measuring your gauges so you know what to look for when you finally upgrade to a more polished set? Check out this handy tutorial!
|
|
This Part has options, please click the button below to order.
730- + Option(s) Livorsi Monster Size Dual Outboard Engine Seven Gauge Kit
We've decided to take some of the guess work our of your next gauge set purchase. By combining the seven most popular gauges we are able to offer you the very best gauges at the very best value.
Monster Gauge sets include:
- (2) 4-5/8" 10000 RPM Tachometer (Electrical)
- (2) 2-5/8" Water Pressure (Mechanical)
- (2) 2-5/8" Water Temperature (Electrical)
- (1) 2-5/8" Fuel Level (Electrical)
Note: Requires 3 plug-In electrical connectors that are sold separately.
ALL LIVORSI GAUGES ARE MADE TO ORDER AND SHIP FROM THE FACTORY IN 2-3 WEEKS.
Livorsi Gauges are available in many color combinations, please select the Rim Style, Rim Color, Face Color and Tach RPM.
Need help measuring your gauges so you know what to look for when you finally upgrade to a more polished set? Check out this handy tutorial!
|
|
This Part has options, please click the button below to order.
730- + Option(s) Livorsi Monster Size Single Inboard Engine Five Gauge Kit
We've decided to take some of the guess work our of your next gauge set purchase. By combining the five most popular gauges we are able to offer you the very best gauges at the very best value.
Monster Gauge sets include:
- 4-5/8" 6000 or 8000 RPM Tachometer
- 2-5/8" Oil Pressure
- 2-5/8" Water Temperature
- 2-5/8" Fuel Level
- 2-5/8" Voltmeter
Note: Plug-In Connectors are sold separately.
ALL LIVORSI GAUGES ARE MADE TO ORDER AND SHIP FROM THE FACTORY IN 2-3 WEEKS.
Livorsi Gauges are available in many color combinations, please select the Rim Style, Rim Color, Face Color and Tach RPM.
Need help measuring your gauges so you know what to look for when you finally upgrade to a more polished set? Check out this handy tutorial!
|
|
This Part has options, please click the button below to order.
730- + Option(s) Livorsi Monster Size Single Outboard Engine Four Gauge Kit
We've decided to take some of the guess work our of your next gauge set purchase. By combining the four most popular gauges we are able to offer you the very best gauges at the very best value.
Monster Gauge sets include:
- 4-5/8" 10000 RPM Tachometer (Electrical)
- 2-5/8" Water Pressure (Mechanical)
- 2-5/8" Water Temperature (Electrical)
- 2-5/8" Fuel Level (Electrical)
Note: Requires 3 plug-In electrical connectors that are sold separately.
ALL LIVORSI GAUGES ARE MADE TO ORDER AND SHIP FROM THE FACTORY IN 2-3 WEEKS.
Livorsi Gauges are available in many color combinations, please select the Rim Style, Rim Color, Face Color and Tach RPM.
Need help measuring your gauges so you know what to look for when you finally upgrade to a more polished set? Check out this handy tutorial!
|
|
730-1000 Livorsi Stainless Steel Elliptical LED Navigation Light Kit - Port and STBD Sides (Green LEDNL3G & Red LEDNL3R)
These L.E.D. bulbs are more energy efficient than standard bulbs. Elliptical navigation lights flush mount into fiberglass for a seamless look, a great alternative to the "bug-eyed" pop-up lights. These lights are designed to be mounted on a vertical surface, to allow the light pattern to be unobstructed from view.
These lights measure 3 1/4" W by 1 3/4" H with a visibility of 2 nautical miles! For use on boats up to 20 meters.
- Polished 316 Stainless Steel
- ABYC & USCG Certified
- NMMA accepted
- Uses round cut-out
- Replaces LEDNL2G and LEDNL2R that use elliptical cut out.
|
|